Autocom Delphi WOW Firmware Versions

[Mister_ACE]

Because demand, here all the firmware of WOW Delphi Autocom. Autocom and Delphi is the same firmware.

Autocom/Delphi Firmware Versions

1130-1220-1230-1310-1320-1321-1331-1410-1423-1430-1520


WOW Wurth Firmware Versions

1130-1220-1231-1310-1321-1410-1412-1423-1430-1515-1521



Added:

CDP+ Delphi_Autocom Firmware Recovery,OTP Area for repair the Firmware you lost-- only for CDP+ and DS150E  so Serial Number 6 digits



If you like my post...press thanks button

[sebasapri]

Thanks mate for the firmware, but i have one question.
I have installed the Autocom 2013.3 and Delphi 2013.3, i know there are a lot version in the forum or internet like 2014.3..... ! the question is ? there are some difference between in 2013 and 2014 , the people sayed a lot of rubish about this, and i have´t a sindrome the las version.
thanks in advance
Seb

[Mister_ACE]

There are many different statements i know, the version 2014.3 have new car inside and mod of Design..and new Firmware..can not tell you whether this works just fine..the basic version is 2013.3 and only modified.

[crewb]

Hi, hope you don't mind me asking a quick question. I have wow 5.00.8 and originally had delphi 2014.2. With these programs my ds150e interface worked with both, no problems. Just upgraded delphi to 2014.3 and now they have different version numbers and can only use one or the other. My question is, should i copy firmware file from wow to delphi? or copy version 2 firmware to version 3? Many Thanks

[Mister_ACE]

Hi copy the firmware from WOW into the Firmwarefolder to Delphi and now runs the Programm WOW and Delphi together. You need the same Firmware in Both Progams and so you have no
issue. You can read here:
http://www.autoprofessionals.org/showthr...6#pid14606 Post 7

[Plastixx]

Hi, I just received my DS150E and installed WOW 5.00.8 R2 and updated the firmware to 1515. Can I use this firmware in 2014.3?

Thanks

[Mister_ACE]

Hi, I just received my DS150E and installed WOW 5.00.8 R2 and updated the firmware to 1515. Can I use this firmware in 2014.3?

Thanks

yes but its better you take the Firmware 1430...for both versions..

http://www.autoprofessionals.org/showthr...6#pid14606   read Post 7

[Plastixx]

Thanks for the reply Mister ACE. I hate to bother you more but you seem very knowledgeable about this device and software. I have a few more questions if that's ok....

Is it normal for the OBD plug LED to never light up? (device seems to function fine other than that)

In WOW I tried to do ABS bleeding under "calibration" for a 2006 Hyundai Tiburon/Coupe. It does not work and the program just shows me a picture of an ODB plug and some message I can't remember. Is this a limitation of WOW or the hardware? Will I have any luck with the process in Autocom/Delphi? This function is the main purpose that I bought the device so it's very disappointing that it doesn't work.

[Mister_ACE]

OBD connector, the LED only lights up when you switch on the front pressing.

Funktion OBD switching on, turn you PC date to 01.08.2013 so you have the full OBD funktion.

Read Post 12 from here:
http://www.autoprofessionals.org/showthr...ht=autocom

[Mister_ACE]

Install the VCI Driver new control panel...you like new Firmware...firmware same read here or Used to the search function.

http://www.autoprofessionals.org/showthr...p?tid=2987 Post 7