Hi.
Small instructions with some files to auto connect to c4 over Wi-Fi!
*****To check if wifi card support adhoc rund cmd as admin and copy paste:*****
netsh wlan set profileparameter name=Road24h ConnectionType=IBSS
Maybe you need to revert back to old drivers, if adhoc is not supported!
I will Start with LAN setup:
1. Open properties to ethernet/LAN card IPv4
2. Enter IP 172.29.127.119 subnetmask: 255.255.255.0 if no communication when doing diagnostic with xentry/DAS try
172.29.127.121 subnetmask: 255.255.255.0
One of those IP's would get you connected to c4! No more needed!
Wi-Fi Setup: Manuel mode (optional)
1. Open properties to Wi-Fi adapter and change IPv4 to
192.168.2.119 or
192.168.2.121
Again, One of these IP's will work when you start diagnostic with Xentry/DAS
Must DO:
Create Adhoc Connection Road24h!
On win 10 Use old Wi-Fi driver to activate adhoc connection. Best Drivers are from 2015! (Change driver in device manager, pick old driver manual stock from win. You do not need to download any driver!)
1. Open Network and Sharing center and click "Set up a new connection or network"
2. Select "Manually connect to a wireless network"
3. Enter Information for the network you want to add:
- Network name: Road24h
- Security type: WEP
- Security Key: 26xa "aaaaaaaaaaaaaaaaaaaaaaaaaa"
- Untick/Unselect "Start this connection automatically"
C4 Wi-Fi automatic mode:
To start "C4Wi-Fi_ON" connection I made a simple batch file, it will enable and dissable wifi card before assign new IP to your Wi-Fi card and connect to Road24h adhoc wich is created!
Also included "C4Wi-Fi_OFF" to revert IP back to automatic so you can use internet!
If stock IP (192.168.2.119) in "c4wifi_ON.bat" is not right you can right click the .bat file and edit to new IP which works for your C4!
Its only one click rather than go back and forth to change IPs. Also your WiFi card name you can edit in the file to match your wifi card name Stock in .bat file is "Wi-Fi".
Its important you have made/created the adhoc connection Road24h in above settings before running .bat file! RUN AS ADMIN!! Copy .bat to Document folder, right click and send to desktop. Right click shortcut on desktop and click advanced, tick "Run as admin". When you click shortcut it will run as admin and do its job!
Please "DO NOT GIVE REP OR THANKS!". Thank you![[Image: smile.gif]](https://mhhauto.com/images/smilies/smile.gif)
just download and enjoy!
PS! For xdos realese after 09.2022 download "WiFi_Toolkit_New_Version_XODS" and run installation to make wifi connection:)
DO NOT USE "Activate Wi-Fi On xentry realese after 09.2021" on early xentry versions!
feel free to comment.
Small instructions with some files to auto connect to c4 over Wi-Fi!
*****To check if wifi card support adhoc rund cmd as admin and copy paste:*****
netsh wlan set profileparameter name=Road24h ConnectionType=IBSS
Maybe you need to revert back to old drivers, if adhoc is not supported!
I will Start with LAN setup:
1. Open properties to ethernet/LAN card IPv4
2. Enter IP 172.29.127.119 subnetmask: 255.255.255.0 if no communication when doing diagnostic with xentry/DAS try
172.29.127.121 subnetmask: 255.255.255.0
One of those IP's would get you connected to c4! No more needed!
Wi-Fi Setup: Manuel mode (optional)
1. Open properties to Wi-Fi adapter and change IPv4 to
192.168.2.119 or
192.168.2.121
Again, One of these IP's will work when you start diagnostic with Xentry/DAS
Must DO:
Create Adhoc Connection Road24h!
On win 10 Use old Wi-Fi driver to activate adhoc connection. Best Drivers are from 2015! (Change driver in device manager, pick old driver manual stock from win. You do not need to download any driver!)
1. Open Network and Sharing center and click "Set up a new connection or network"
2. Select "Manually connect to a wireless network"
3. Enter Information for the network you want to add:
- Network name: Road24h
- Security type: WEP
- Security Key: 26xa "aaaaaaaaaaaaaaaaaaaaaaaaaa"
- Untick/Unselect "Start this connection automatically"
C4 Wi-Fi automatic mode:
To start "C4Wi-Fi_ON" connection I made a simple batch file, it will enable and dissable wifi card before assign new IP to your Wi-Fi card and connect to Road24h adhoc wich is created!
Also included "C4Wi-Fi_OFF" to revert IP back to automatic so you can use internet!
If stock IP (192.168.2.119) in "c4wifi_ON.bat" is not right you can right click the .bat file and edit to new IP which works for your C4!
Its only one click rather than go back and forth to change IPs. Also your WiFi card name you can edit in the file to match your wifi card name Stock in .bat file is "Wi-Fi".
Its important you have made/created the adhoc connection Road24h in above settings before running .bat file! RUN AS ADMIN!! Copy .bat to Document folder, right click and send to desktop. Right click shortcut on desktop and click advanced, tick "Run as admin". When you click shortcut it will run as admin and do its job!
Please "DO NOT GIVE REP OR THANKS!". Thank you
just download and enjoy!PS! For xdos realese after 09.2022 download "WiFi_Toolkit_New_Version_XODS" and run installation to make wifi connection:)
DO NOT USE "Activate Wi-Fi On xentry realese after 09.2021" on early xentry versions!
feel free to comment.