+- AutoProfessionals (https://www.autoprofessionals.org)
+-- Forum: Auto-Professionals Other Forums (https://www.autoprofessionals.org/forumdisplay.php?fid=269)
+--- Forum: Selling Box / Commercial Section - Sale / Purchase - Market Place Area - Trade Your Stuff (https://www.autoprofessionals.org/forumdisplay.php?fid=292)
+--- Thread: FULLY REWORKED KESS V2.23 / 5.017 (/showthread.php?tid=7659)
FULLY REWORKED KESS V2.23 / 5.017 - robni455 - 18-01-2018
KESS V2 2.23/5.017
FULLY REWORKED UNIT
ALL PROTOCOLS OPEN
CARS BIKES BOATS TRUCKS TRACTORS TRICORE
NO TOKENS
ALL CABLES + HELP FILES
INTERNET SAFE
VIRTUAL READ SUPPORTED
*******************************
logic.
FAQ:
1.Q: Why does this KESS V2 cost more than any other unit on the internet?
A: We sell two types of units. This particular unit is called FULLY REWORKED. This unit will function exactly as the original without any issues or failure. The units start as china units that we source from a factory that have the best pcbs. We then remove and replace any components that are prone to failure. These units carry a 1yr no questions asked warranty and are guaranteed to work exactly as an original KESS V2. Our other units are called TrueEU and are' of the highest quality, actually better quality than an original unit. We also sell these units on eBay, for around twice the price as our Fully Reworked Units. Please see our other listings.
2.Q: Where is this unit manufactured?
A: Our PCB is manufactured in China, it is then brought to the EU where we disassemble it completely and rework the entire unit where it is finally tested in the EU. It goes through the strictest quality assurance testing before each unit is shipped.
3.Q: Does Virtual Read work with this unit?
A: Yes you can make virtual read with this unit. However you will need to purchase second half of file from someone with ATech Subscription.
4.Q: Is KESS V2 Master or Slave?
A: Master Version
5.Q: Can KESS V2 update?
A: If an update is released you can purchase new NXP + SDCARD to update, or you can send back in unit to us for upgrade. These units CANNOT be updated online
6.Q:Does KESS V2 need to be activated?
A:No it does not have to be activated
7.Q: What operating system can KESS V2 be installed on?
A: Our software is custom made and has drivers for ALL VERSIONS of WINDOWS, WINDOWS XP, 7, 8.1, and 10. You must install this software AS ADMINISTRATOR
8.Q: KESS V2 is showing the error “Connections not established” ?
A: Either you have a bad USB cable, you can check this via the device manager in windows. If the usb cable is good, but you do not see KESS V2 in device manager please reinstall as administrator.
9.Q: After Ksuite opens all of the icons are greyed out? What is the problem?
A: Please disconnect network connection and restart ksuite. All protocols should be OK now. This happens sometimes if you have a specific firewall rule enabled on your laptop or router.
10.Q: Can my KESS V2 work with EDC17
A: Yes, Our TrueEU KESS V2 can work with EVERY PROTOCOL that is available inside ksuite, EDC17 included. Most likely you will be using the TRICORE cable and BOOTP module to read/write these ecus.
11.Q: Can my KESS V2 make correct checksums?
A: Checksum is automatically corrected as you are performing a write
12.Q: When I try to make some trucks or tractors with KESS V2 it is asking for specific cables that aren't included?
A: Please contact us for additional accesssory cables for Trucks and Tractors. There are some vehicles that don't accept the standard OBD2 connector. In this case we do sell additional cables to fit the Tractor or Truck that your working on.